The Great Escape

This time of year always feels like Groundhog Day – go to  work, go to sleep, wake up, do it again.  It becomes so repetitive that it leaks into your mind, filling your thoughts so there is little room for anything else.  This year it’s amplified by the negativity surrounding my work.  All that combined with no riding for dark months on end and it’s hard not to get jammed.

If I time it right I can sneak out of Ontario on an above zero, dry road day.  You can still find double digital daily highs in Cincinatti and south.  A plugged in electric kit bonzai ride to Cinci and I’m out of the snowbelt.  From there it’s a less ragged ride south to New Orleans.  From Cinci I’d angle over to Memphis and follow the Mississipi down to the Big Easy…



After reading books like Todd Blubaugh’s Too Far Gone and watching Austin Vince Mondo Enduro the planet, I’ve often wondered what it would be like to get lost on the road.  Once out of the snowbelt, I’d be in no rush to be somewhere.  Without that very Western time fixation, I wouldn’t have to get wound up over deadlines.


If I’m not fixated on a destination the daily goals might not be that linear.  With local knowledge I’d hope to find things off the beaten path as I meander…





Off the top of my head, I’d leave New Orleans along the Gulf, visit Austin and then ride the Twisted Sisters in Texas Hill Country.  Austin’s also the home of the only North American MotoGP race, so if I timed my return with the race, I could be passing back through Austin on the way home in early April and catch Marc and the rest of the aliens doing their thing.  The goal on the way south would be to get familiar with Austin’s weirdness for the return stop.

After wandering Texas I’d take a run up to the Very Large Array in New Mexico and do my best Jodi Foster immitation.  New Mexico and Arizona have a pile of strange sites to see, so the wandering would get intense.  Norman Reedus did a Ride episode in New Mexico that does a good job of showing what’s on hand out there.

Even that far south the mountains can also catch you out with northern temperatures as we found out a couple of years ago in the Superstition Mountains just outside of Phoenix in early January, so not rushing and timing your rides is important when at altitude.  There are pile of old western towns and ruins in the US South West, along with some astonishing pieces of engineering.  Meandering from photo opportunity to photo opportunity would be a nice way to ease into this slow motion ride.

Tuscon is home of the Aeroplane Boneyard where thousands of retired air force planes sit in the desert.   A wander around there at sunset would be a glorious thing.  I’ve done the Phoenix area a couple of times and travelled from the north end of Arizona from Las Vegas, but haven’t travelled as far south as Tuscon.  From there I’d head across to Yuma, another famous western US location, before diving south into the Baja Penninsula.  A desert riding tour would be a pretty cool way of seeing Baja.

Mexico is a whole other world.  Most riding-the-Americas types blitz through it looking for a fast route south,but Mexico (with a final lunge into Belize) is where I’d wrap up this great escape from the never ending Canadian winter.  Some crystal caves, Mesoamerican pyramids and Belize beaches during the deep freeze and then working my way back up to Austin for early April…


Seeing the Ozarks and the Tail of the Dragon during the weeks after the race would be a nice way to wind up this great escape, getting back to the frozen north just as it’s not frozen anymore.

from Blogger https://ift.tt/2M5KPUG
via IFTTT

3d modelling madness

I got a Structure 3d scanner this week at work. We’re using it there for all sorts of educational activities, but I find myself painting the various Kawasaki products in my garage.

This thing costs about $350 bucks and straps on to an ipad.  You walk around your target ‘painting’ it on the ipad screen (it looks like you’re covering it in clay) and then you’re done.  Any of these motorcycle models took about a minute of walking around the bike…







It didn’t take me long to get some remarkably detailed images of the Concours












Because it’s so easy to paint an object and create a 3d model out of it, you tend to try all sorts of angles.








The scanner will also take a swing at rooms, though I’m not so good with them yet.  This is an image of the garage.  The Ninja is on the left, the Concours is further in on the right.

The file generated is basically a list of vertices connected by lines.  The sensor measures distances and constructs a 3d mesh out of them.  The result is a three dimensional image.

How could something like this be used?

You could scan a fairing or other part, get accurate geometry out of it and then modify it digitally before printing out a replacement.



I think I’m about five years away from being able to 3d print my own digitally modelled custom fairings for any bike.  The hold up right now is a 3d printer big enough to manage large prints.  What I’d really like is a high resolution Terminator 2 style Formlabs printer like the one below that’ll print up to fairing sized pieces…

Frank Lloyd Wright’s House

Lloyd Wright’s only motorbike… he designed 70 odd cars though.

What does Frank Lloyd Wright have to do with motorcycles?  Well, he designed one.  In addition to that one 1930s Harley he also designed dozens of cars, including some pretty iconic ones like the VW Mini-Bus and the original gull-wing Mercedes 300.

I went on a tour around Wright’s house, Taliesin West, in Scottsdale and was blown away by this polymath’s genius.  I’m not that sharp, maybe just bright enough to recognize genius, but it leaves me in awe.  I always end up leaving places like Taliesin West thinking that a big part of genius is just not giving a shit about what other people think.  Free from social constraints geniuses are able to follow their urges and amaze the rest of us with their discoveries.  Just don’t get too close to one.


It’s covered in soot because it belches fire…

From reading Nietzsche to wandering around the Van Gogh Museum to seeing the world Wright made for himself, you can’t help but wonder what it must be like to be that free of social expectation.  That freedom is what Wright exploits to create an aesthetic that is truly iconic and unique.

Being free from the shackles of society, Wright, like Van Gogh and Nietzsche, make a real mess of their lives.  It’s in that glorious mess that their genius is realized.

Sherlock does a good job of showing just how broken genius can be.


Our tour guide told us the story of Taliesin’s water.  They used to haul it up onto the plateau where it’s located (miles from the Scottsdale of the day).  Wright decided he wanted a well dug so he called a guy up and had him dig even though the guy had been up on the ridge before and knew there was no water to be had up there.  


At 200 feet the well digger stopped.  He didn’t have the gear to go any further.  Wright made a fuss and told the guy to go and get what he needed to go deeper.  He finally struck water at almost 500 feet, and Taliesin has had its own water supply ever since (it’s wonderfully cold and tastes fantastic).  Wright never paid the well digger.


You have to wonder how many people geniuses use and throw away in order to express their genius.  Teliesin West is a work of art that needed water and Frank made it happen, but he broke a man’s livelihood in the process.  No one remembers that though and the art lives on.  The social calculus of genius is interesting – many people continue to benefit from Wright’s genius.  The people close to him who paid for it are all forgotten and long gone.


I wish I could go back in time and buy that well digger a beer.  It sounds like he needed one.

The house that Frank built (and didn’t pay for),

 

Naked Connie: 3d modelling customized motorcycle bodywork

I’ve re-3d-scanned the stripped down ZG1000 Kawasaki Concours in order to better work out what the rear lights will look like.  You can wheel in and out and manipulate that model below with a mouse.  The scanner did a bunch of software updates which led to a much higher resolution 3d image.


I modelled it with the stock seat on with an eye to taking the pillion seat off and building a very minimal back end.  With some careful cutting I’ll be able to use the seat dimensions to figure out how best to render the rear light assembly.  I’ve been doing 2-d drawings but they don’t deal with the 3d complexities of the real thing.  I’m hoping this solves that.

Using the 3d scanner with cardboard body panel templates gives you a pretty good idea of how it will look when it’s done.


As far as electronic parts go, I think it’s time to get the lights sorted out.  At the moment I’m looking at some integrated LED head and tail lights to minimize stalks sticking out of the bodywork.

A single brake and indicator unit from Amazon.
Integrated LED headlamp from Amazon.



via Blogger http://ift.tt/2ha9rNw

Escarpment Murals

A hot and sunny Sunday ride up and around the Niagara Escarpment looking for murals, though the twisty roads were the main focus…


Part 1: https://goo.gl/maps/QseRL6TWNhq
Part 2:  https://goo.gl/maps/BgC2rUvH2qQ2
293kms


The PTTR Grand Tour is going on all summer through Lobo Loco RalliesPaint the town red 2018 Grand Tour   That one is closed now, but there are many other weekend rallies going on if you’re interested in exploring long distance motorcycle rallying.  


Murals Discovered:
Grand Valley 43.898875, -80.315307



Creemore 44.326060, -80.106099



Ravenna Country Market 44.469285, -80.417343



Clarksburg  44.546531, -80.461742



Some other 360 imaging from the ride.  Made using the Ricoh Theta camera on a flexible tripod attached to the bike:

The twisty bits on River Road

In Thornbury on the shore of Georgian Bay – the temperature was easily ten degrees cooler.

Beaver Valley

A busy Sunday in Creemore.

Through the wind fields outside of Shelburne



You can learn how to get shots like this HERE.

from Blogger https://ift.tt/2zmOhGz
via IFTTT

Haliburton Highlands Fall Colours

With the weather beginning to turn we’re in for a Canadian treat:  Fall Colours.  I think I’m going to aim for a couple of days out Haliburton way in October for a last big ride and a chance to soak up the colours.


Last time up that way I did Highway 60 through Algonquin Park.  This time I’m going to stitch together another route that is as different as possible.


Algonquin does a colour report that I’ll keep an eye on and see if we can time a couple of days up that way when the colours are peaking.  Discover Muskoka does one too.  Last year we went up to the Kawarthas for Thanksgiving (early October in Canada): 



…and it was right before the colours changed.  Only the somac was in full colour.  I’ll see if I can time it a bit better this time around at sync it up with a big last ride before the snows come.


Autumn on the Canadian Shield is a beautiful thing.

from Blogger http://ift.tt/2gTArCP
via IFTTT

Triumph Tiger 955i Engine Remapping

There are a number of posts on this blog about working out the kinks in my 2003 Triumph Tiger 955i,

and this is another one.  I’ve been playing with the Tuneboy engine management software that came with the bike, which works well, is put together well and is easy to use.  In working with the Tuneboy kit I discovered TUNEECU, a more open-source option for programming your own engine maps.

If you’ve never wrapped your head around engine maps, they’re not very complicated.  Tuneboy does a good job of explaining how it works in their primer that comes with their software.

Back in the day you had a carburetor that used screws and jets to set the amount of fuel that got metered into the engine.   If you changed altitude you had to start swapping hard parts (usually the jets that sprayed fuel) to keep the bike running right, and sooner than later you had to manually trim the whole thing to keep it running right.  Electronic fuel injection took that all away.  A computer under the passenger seat on the Tiger takes inputs from sensors in the air-box (barometric pressure), in each of the three injectors , the fuel pump, radiator (engine temperature) and a crankcase sensor to constantly adjust things to use the most effective amount of fuel to make the bike go.  Put another way, carburetors are a mechanical, low resolution solution to feeding fuel into an engine.  Electronic fuel injection is a responsive, high resolution fix to the problem of delivering the right amount of fuel to a motor.

Tuneboy map editor – you can change settings and tell
the ECU (electronic control unit) what to do under
certain circumstances.

A fuel map is a spreadsheet of numbers.  Sensors feed the computer what RPM the engine is turning at and how much throttle is being asked for and based on the number in the fuel map, the computer delivers a set amount of fuel.  The ‘fuel map’ is literally a map that directs the computer to deliver a set amount of fuel.  If you’re at high RPM and have just shut off the throttle, a smart EFI system will cut fuel delivery entirely, saving both fuel and emissions, something a carb couldn’t manage.  If you suddenly give the bike a handful of throttle at low RPM, the map will direct the fuel injectors to deliver an optimal amount of fuel as it picks up speed, whereas a carb will always just send a mechanically set amount of fuel based only on how much wrist you’re giving it.

In Tuneboy’s system, you can change fueling and ignition maps, and modify things like idle speeds. The issue has been that the only maps I can find for Tuneboy are the stock ones from Triumph, which were set up to favour fuel economy and emissions over smoothness and drive-ability.  Meanwhile, TUNEECU (if you can navigate their 90’s style web design and atrocious apostrophe use) offers you modified tunes that can smooth out your lumpy OEM map.


Of special interest to me were custom edits that made the list and have been on there for 9 years.  I don’t know who Deano from South Africa/SA_Rider is, but they know their stuff.  The map on there does wonders for your Tiger’s smoothness and pickup.  It might use a bit more fuel if you’re heavy handed, but the difference in motor operation is impressive and worth it.


I was unable to find a digital tool to transpose the HEX files from TuneECU into my Tuneboy DAT format, so I opened up the modified HEX file and transposed the numbers over to the Default Tuneboy 10120 Triumph engine map and resaved it.  You can find that modified Tuneboy DAT file with the TuneECU South African mode here.

Finding this stuff isn’t easy, and it’s only getting harder as these old bike recede into the past, so I’m hoping this post help you find what you need to get your Tiger purring again.  It did wonders for mine.
Even though the old vacuum pipes held vacuum, I swapped them out for some similarly sized clear fuel line I had (you can see them going from above each injector to the idle stepper motor.  The TUNEboy software also comes with a diagnostics tool (with very cool 90s graphics!) that lets you test the radiator fan, idle stepper motor (which moves up and down modulating the vacuum in that black thing to the left/bottom in the picture) and the RPM gauge.

LINKS

You can find TUNEboy here:  https://www.tuneboy.com.au/
It comes with a cable that’ll connect to your Triumph and is easy to get going, and comes with all the stock tunes.  It also lets you tune on a dyno, if you’re minted.  It ain’t cheap, but the minted guy who bought my bike new was, so he sprung for it and I’m still enjoying his largess over a decade later.

TuneECU can be found here:  https://www.tuneecu.net/TuneECU_En/links.html  Try to get past the out of control apostrophe use – they’re better at software than they are at the speaking English goodly.
The older version is free, but finicky with Windows’ old serial port drivers.  You can buy the app on the Android store for fifteen bucks, which seems perfectly reasonable.  You can then connect via bluetooth from a phone or Google tablet, though I understand you miss some connectivity that way.

It gets tricky these days finding the On Board Diagnostics (OBD) serial cable you need to connect the bike to the PC.  You can buy ’em from the UK, where people like fixing things.  CJ Designs in Wisconsin will sort you out with one too:  https://cjdesignsllc.com/?s=TuneECU

The modded engine maps for Triumphs on TuneECU can be found here: https://www.tuneecu.net/Custom_Tune_list.html

The TuneECU page goes into detail about how you might use the TUNEboy cable, but it requires so much messing around with knocking default Windows drivers out of the way and forcing others on that I wouldn’t bother (I didn’t).

from Blogger https://ift.tt/3kEyiat
via IFTTT

Motorcycle Carburetor Rebuild Part Eleventy-Seven (airbox boots)

The carburetor rebuild grinds on.  It took the better part of a week to get the airbox boots in, and when I opened the bag they came in I’d been charged for four but only got three.  I tried contacting Two Wheel Motorsports to ask if the fourth boot was sitting around there, but they didn’t get back to me.  

The Concours uses two types of boots to connect the carbs to the airbox and one of the old ones still had pretty good flexibility in it, so I used the three new ones and the best of the old ones.

I tried for the better part of two hours to get the carbs mated to the airbox properly with the stiff, old airbox boots without success.  With my home-made hooked screwdriver (to slip the boots onto the intakes) it took about ten minutes of adjusting to get a good seal on all four carbs.  If you’re doing an old carb rebuild, buy some new airbox boots, it’ll save you a  lot of frustration and swearing.

The old airbox boots look rough, but the real issue is that the rubber has hardened over time and no amount of heat will soften them up.  The new boots were supple and easily went on the carb air intakes with minimal fuss and bother.
I pay for four and get three.  Fortunately one of the old ones was still pretty supple so I could reuse it.
Ten minutes and the carbs are back in place.  Get new airbox boots if you’re rebuilding an old carb!

 

Riders & Tigers & Rivers (oh my)

a 2003 Triumph Tiger 955i… sketch!

A somewhat-warm and sunny Saturday meant a short ride up and down the river banks.


With a dirth of twisting roads around here, the Grand River is one of the few geological obsticles that forces local roads to do anything other than travel arrow straight.

It was a nice ride with a lot of bikes out and about.  At one point, waiting to turn onto the highway, I came across half a dozen BMWs and a lone Suzuki Vstrom – the local BMW club and a friend?

Were I lucky enough to live near some mountainous terrain, I’d be bending the bike around some real corners.


Saturday morning had me cleaning up my gear (check out those shiny boots in the video!) and fixing my Roof helmet.  I love that thing, best helmet I’ve ever owned.  I’d be heartbroken if I couldn’t fix it.  The plastic cams had gone out of alignment on the visor.  The last time I closed it they snapped, leaving me with an always open helmet.  Fortunately I had a spare set that came with the original clear visor.  It took a bit of aligning, but everything went back together flawlessly.

That Roof is one of the only ones in Canada.  I’d need to take a trip to Europe just to get another!  I’m starting to regret only buying one when I had a chance to pick up the last ones in Canada.




Pandemicky Cancellations And Alternate Means

Thanksgiving weekend in Canada was to be my last big ride of the season.  It’s been a tough year and the chance to get away from the pressure cooker of teaching in a pandemic was something I was clinging to a bit too tight.  The daring plan was to finish another exhausting week of teaching in a too small masks in classrooms that are ignoring all the pandemic rules everyone else is following, get a much needed night of sleep and then make my way up to ride the Haliburton Highlands in all their autumn glory before spending a weekend far away from the noise of pandemicky 2020 in the woods near Bobcaygeon.  The ride back would have been 274 kms of backroads less travelled.


I discovered Friday afternoon that we’d been waved off from the in-law’s cottage because we’re too much of a pandemic risk.  The irony that I can’t get away from the thing that strangles me each week because I’m getting strangled by it each week isn’t lost on me.  Instead I took the sunny and 22°C forecast and headed up to Hornings Mills and River Road for some Niagara Escarpment twisties, except I never got there because forty minutes up the road just north of 89 in Shelburne the rain started to fall.


I turned around and came home again.  Riding with purpose through rain is an enjoyable experience.  The smells and feel during a rainy ride are unique and worth pursuing, but looking for rain when you’re on yet another pointless pandemic loop over familiar roads doesn’t make much sense, so I turned around and went home again.  Autumn colours were lovely and the Tiger ran like a top though.


The fire we thought we’d have that night didn’t happen because everything was wet.  The next day opened sunny and cold, but warmed up to the point where we went for a walk in the woods nearby.

When we got home I backed the Honda out of the garage and went for a ride in the cool, clear, autumn air.


Any weekend where you can take each of your two bikes out for a ride isn’t a bad weekend.  Soon enough we’ll be buried under a blanket of snow while the second wave of the coronavirus spreads in the closed places we share, like my classroom.  


The kick in the groin here was getting dumped by family on the weekend we were aiming to be away without warning.  Nothing like your own family treating you like a plague cow to really drive home the meaning of Thanksgiving.  What really burns my ass is having to depend on them to be able to access the things I was looking for:
  • getting away from the godforsaken suburbs and into THE WILD
  • off roading with my son
  • hanging out on a hammock in the wilderness with my wife
  • having a reason to ride beyond my usually riding range
  • being comfortable while we do it

I don’t live in the right generation to own a cottage (and the generation that does isn’t sharing during a pandemic), so I need to work out a way where I can check those boxes without depending on the vagaries of other people.  My wife won’t sleep on the ground any more so camping won’t cut it, but maybe a camper might.


A Skala Conversions Ram Promaster would do the trick.  With the right sized motor and towing package, we’d be able to tow my son’s ATV and my dirtbike into the woods and find our bliss without depending on anyone else.  Some crafty engineering and smart packaging and we could be mobile and efficient without a ludicrously large camper.  A membership with the OFTR and we could enjoy off roading together in a variety of different places and glamp like rock stars.  When we just wanted to disappear into the wilderness we could do that too.

A cheaper alternative is a used camper, and there are many about.  Eight grand’ll get you a low mileage older small camper.  The Roadtrek RS Adventurous looks promising and arrives in 2021. It gets great mileage (like 20mpg) and sleeps up to four.


If I had the shop space and time I’d go grab this disco 1974 ‘RekVee’ from where it’s parked up near Perry Sound for five hundred bucks, throw it on a flatbed and bring it back, strip it down and convert it to an electric/hybrid.  The electric RV isn’t viable yet with our medieval chemical battery technology but a hybrid diesel/electric option would work.


One way or another I want to get off the depending on other people to decide access to my mental health getaways.  What’s nice about the RV option is that it works while we’re in lock down.  Ontario is a big place and socially isolating when you’ve thousands of miles of wilderness north of you and your own place to sleep is perfectly doable).  When things open up again we could take the thing to Ushuaia.

In other circumstances we’ve gotten ourselves into a hotel when the cottage politics gets too thick, but the pandemic makes that next to impossible.  I need to engineer more flexibility and capability into our escape plans so we get to be the arbiters of our own mental health excursions. 

from Blogger https://ift.tt/2SOmBRZ
via IFTTT