On Going Historical Research: 1930s Off road riding

https://www.bonhams.com/auctions/18221/lot/460/

1930 Scottish Six Day Trial bike and the enigmatic Ms E Sturt
previous S6DT winners

Beer, and war!

from Blogger https://ift.tt/3kEh8Jf
via IFTTT

Brake System Maintenance on a C14 Kawasaki Concours

 I’m busy in the garage these days with the on-going 50 year old Triumph Bonneville restoration project.  It’s a big project that will take some time to sort out, but it’s -20°C outside with snow squall warnings of 20cm of snow coming, which means it’s also regular maintenance time on the two running bikes in the stable.

Tiger’s back in hibernation after last week’s sprockets & chain maintenance, waiting for a break in another never-ending winter of COVID for a chance to ride.

Last week the Tiger got new chain and sprockets.  I hadn’t done the sprockets on it since getting it over 5 years and 40k ago, so I figured it was time when I noticed the latest chain had stretch in it that made it impossible to set the sag properly.  This week it’s all about the Concours.

I got the Connie last spring in the middle of the second lockdown.  My son and I rented a van and drove down to The Beaches in Toronto and picked it up from its second owner who hadn’t been riding it for several years.  It’s a very low mileage bike (under 30k when I picked it up), but I like to cover all the basic maintenance so I can set a ‘zero point’ for future work.

As you would expect from Kawasaki Heavy Industries, the brakes on the GTR1400/C14 Concours are superbly engineered Nissin calipers.  I’d picked up the pads last summer but they hung on the wall until now because I was putting miles on the thing.  I did find the brakes were squeaking a bit, suggesting the calipers weren’t releasing properly – something that can happen in a bike that sits for several seasons.  Like I said before, I don’t like riding a bike where I’m not sure of the maintenance, especially on brakes, so it was due.

Doing the pads on the Concours is remarkably easy.  You don’t need to remove any body panels and everything is very accessible.  Undo the pin that holds the pads and spring that holds them in and then everything comes apart in your hands.  The pins were rough and there was some odd gunk stuck in the front right caliper.  I cleaned everything up and lubed it and then slotted the new pads into place with the now lubed pins (I think it’s a #5 hex head that does the trick).  All very logical.

If you’re looking for torque settings for the
brakes on a Kawasaki GTR1400/Concours
C14, here they are.

The rears are just as easy and a similar design with the same pin and caliper bolt sizes (everything is hex metric).  The back was as mucky as the front and I went to lengths to clean up the pressurized caliper slider and lube the pins and areas where the pads move.  The action immediately felt better afterwards.

Last spring when I got the bike I had to sort out a leak in the hydraulic clutch which resulted in entirely new DOT 4 brake fluid (what the Connie uses in both clutch and brakes).  Changing up your brake fluid removes impurities and moisture that can eventually cause real corrosion headaches in your brake system, so after doing the pads I changed up the brakes fluid on both front and rear systems.  The only fluid change left now on the Concours is the antifreeze.  I’ll do that at the end of next season.  When I tested it the fluid it was still bright green, looked new and showed good temperature range.

Getting all the air out of the hydraulic clutch so that it felt tight and had positive action was a real pain in the ass last spring.  The good new is that this air-line powered vacuum system did the trick then (it’s not crazy expensive) and takes the headache out of bleeding anything with steady, controllable suction.

In the case of the brake system, I set up the vacuum bleeder and then kept adding fluid in the reservoir at the top until it came out clear (the used stuff was darker and cloudier – it looked almost like water once the new stuff made an appearance.
Just a note:  don’t keep brake fluid laying around open.  It collects moisture and goes off pretty quickly.  As with all brake fluid changes, I opened the bottle and then immediately used it this time.
The front brakes took less than 10 minutes to completely bleed of old fluid and the rears even less.  If you’re doing your own brake/hydraulic fluid maintenance with any kind of regularity, let that hand-pump go and get one of these things (assuming you have an air compressor of course).
With the brakes sorted on the Concours and the sprockets and chain on the Tiger, both are waiting for a break in the weather for a cheeky winter ride to kick off the 2022 season.  As long as I’m not trying to navigate ice on the road, I’m good to go.  An above zero day and some dry pavement is all I need

Now that the regular movers (I was going to call them new but the Tiger is almost 20 years old and the Connie turned ten last year) are sorted out maintenance wise, it’s back to the old Bonneville project.  Next up I’m rebuilding the two Amal carbs, then it’s rebuilding the ignition system and then (hopefully) hearing the old thing bark for the first time in decades.

Sometimes the Bonneville can feel like it’s too big to manage, it needs so much, but with two other working machines I’m never going to be angry with it not being ready, though I would love to have it running in time for The Distinguished Gentleman’s Ride on May 22nd.  A ’71 Bonneville with some early 70s retro style would be a blast.

from Blogger https://ift.tt/3FapNgG
via IFTTT

3d Modelling & Imaging

Through work I’ve done a fair bit of 3d modelling and imaging.  A cheap and easy to use 3d scanner is the Structure Sensor, a laser scanner that clips on to an ipad and quickly builds a 3d model by painting it with a distance sensing laser.  It takes the distances and builds up a model of polygons from the location data.  


Using that process I’ve rendered 3d models as well as 2d images of them.  I use Sketchfab to upload 3d models to the web to share them.  2d images are typically screen captures of the 3d models either off the ipad after the Structure Sensor scan or out of Sketchfab after they’ve been uploaded.


Here are some examples:




This is a 3d print of the Tigertester model above.
These black and white images are off the Structure Sensor software on the ipad (in xray mode).

You can skin the image to give it colour, this is an example of the skin that would go over the wire frame model to render it in full colour.



LINKS:

3d modelling & graphic design work on motorcycles.
3d modelling & graphic design in the classroom.





from Blogger http://ift.tt/2C88RHF
via IFTTT

Love It When They Do This

 

This popped up on my Facebook feed.  I actually contacted the local dealer about this one last year and asked if he’d consider $6500 – he couldn’t be bothered to email me back even to barter; love that arrogance.

This is a first gen Concours C14 with almost 60,000 kms on it.  I ended up picking up a second gen C14 that was two years newer with half the kilometers on it for $5500.  I had to put a bit of time in on it sorting out the electric windscreen, a clutch gasket and picking it up and safetying it.  $5500 for the bike, $120 for the rental van to get it, $20 in parts (from Two Wheel!) and $90 to get it safetied with a $715 tax bill still had it all costing me less than $6500 on the road.  Thanks to that price they’ll be looking at over $300 more just in taxes for the lucky new owner.

Even with my fancy German windshield and American saddle I’m still coming out ahead.  Prefer the colour on mine too.

from Blogger https://ift.tt/3f39sQl
via IFTTT

Changing Motorcycle Chain And Sprockets

I’ve done chains before but not sprockets.  It’s a fairly straightforward bit of work you can do yourself in your shed/garage.  In this case I’m doing both sprockets and chain on my 2003 Triumph Tiger 955i which has over 80k on it.

With the bike on its centre stand I removed the rear tire.

I picked up a chain breaking and installation tool a couple of years ago and it has more than paid for itself.  It has pin sets that push chain pins out to break the chain (it keeps all the hardware in the handle so for the two+ years I don’t use it I’m not losing parts).

It also has drop in pads that let me press new rivet chain connectors together.

The new vs. the old front sprocket.  The new one is 19 teeth, the old one 18.

The new front sprocket on the motor.  These are the parts I used:

RK 530 MAX-O O-Ring Chain Natural 114            $101.99
JT Steel Rear Sprocket 46T (530) JTR2010.46    $74.99
JT Steel Front Sprocket 19T (530) – JTF11           $80.19 (all prices CAD)
The ’03 Tiger takes a 114 link chain, a 46 tooth rear sprocket and an 18 tooth front sprocket stock.  I saw a suggestion online that going to a 19 tooth front sprocket calms down the bike a touch (it can be jumpy off the line) while also revving a touch slower while cruising which should improve mileage a bit.

Not bad for the original stock rear wheel with over 80k on it, eh?  If you think modern Triumphs aren’t well put together, this one was, and with quality parts.

I’ve had these on the bike since I got it over 30k ago.  Still not in terrible shape.  I’ve seen sprockets torn to shreds – some people must be very heavy handed on the controls to strip a socket like that.  I’ve had the Tiger pulling the front wheel off the ground under acceleration so it’s not like I’m soft with it (it’s getting this drive train maintenance because the old chain had stretched in places).  I’m curious to see and hear how the new parts work.

The new chain and sprockets on.

The connecting link (see it?) is pressed into place with the DRC chain tool which also pushes links together as well as pulling them apart..

The many directions and warnings on the back of the chain box.

The Tiger had a deep maintenance last year, so this year it only needed the chain & sprockets.  It’s back under the blanket waiting for a break in the snow for a cheeky early-spring ride.  Next up is doing the brakes on the Kawasaki, then I’m into rebuilding the Amal carbs on the 50 year old Bonneville winter project.

If you’re looking for torque settings and parts details for a 2003 Triumph Tiger 955i while doing a sprocket and chain, here they are:

  1. chain sag:  35-40mm
  2. drive chain adjuster (the clamp on the adjustable rings in the swingarm):  35Nm
  3. rear sprocket nuts:  85Nm
  4. front sprocket nut:  132Nm
  5. rear wheel axle bolt:  85Nm
  6. 530 chain with 114 links (if that seems confusing, check THIS out)
  7. 18 tooth front sprocket (though 19 is recommended)
  8. 46 tooth rear sprocket

from Blogger https://ift.tt/3EK0p0R
via IFTTT

Motorcycle Electrical System Rebuild From Scratch

Researched links on re-wiring the 1971 Triumph Bonneville… 

The old Bonnie has an intact loom and many of the original electrical components, but many of these pieces won’t have weathered the decades well and I’d be crazy to try and rebuild a hacked on electrical system in a fifty year old bike, so it’s all coming out.  I’m going to take a page from the custom scene and build a loom from scratch and design and build a complete electrical system from scratch.

This ain’t no modern digital machine so the electrical system in it is prehistorically simple.  Building a dependable replacement with quality modern upgrades (proper copper wiring, modern connectors, new electronic ignition and coils, etc).  The result should be a 1971 Bonneville that is more spritely and dependable than anything that rolled off the line in Meriden in 1971.

Tutorials on creating a motorcycle wiring harness/loom:

BikeExif Tutorial: https://www.bikeexif.com/motorcycle-wiring

Rewiring tutorial:  https://www.liveabout.com/making-a-motorcycle-wiring-harness-743591

Tutorial:  https://purposebuiltmoto.com/motorcycle-electrics-101-re-wiring-your-cafe-racer/

Tutorial: https://www.hagerty.com/media/maintenance-and-tech/building-wiring-harness-from-schematic-to-bundle/

Resource (costs 20 pounds): https://rupesrewires.com/build-your-own-wiring-loom-pdf-book/

Another good resource ($40): https://www.amazon.ca/gp/product/0760345368/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1

I’ve purchased and read that last one – it’s a gentle introduction to electrical work but I found it a bit simple and wished it had picked up speed as it went.  If you’ve never done any electrical work then it’s a good place to start, but that’s what I do all day so I was hoping for something with a bit more depth.

Replacement harness:

http://www.britishwiring.com/MC-28-PP-p/mc28pp.htm

Prebuilt ’71 Bonneville wiring harness: https://www.thebonnevilleshop.com/product/lucas-71-72-triumph-bsa-650-twins-main-cloth-wiring-harness-pn-54959629-g-99-1222-g/

Original loom wiring colours:
  • RED (seems to be earth but then battery + so this is a positive earthed bike?)
  • WHITE (headlamp loom)
  • GREEN/WHITE STRIPE (LH handlebar switch & main loom)
  • BROWN/GREEN STRIPE (headlamp loom)
  • BROWN/GREEN STRIPE (headlamp loom)
  • WHITE/YELLOW STRIPE (L/H handlebar switch) + ignition coil
  • BROWN (headlamp switch)
  • GREEN/RED STRIPE (L/H handlebar switch)
  • PURPLE (horn press R/H switch)
  • LIGHT GREEN (L/H handlebar switch)
  • PURPLE/RED (earth?) horn
  • BLACK/WHITE STRIPE / BLACK/YELLOW STRIPE (contact breakers)
  • BLACK/WHITE STRIPE (condesner pack/ignition coil split)
  • RECTIFIER:  WHITE/GREEN STRIPE + GREEN/YELLOW STRIPE+BROWN/BLUE STRIPE+RED (earth)
  • IGNITION COIL: BLACK/YELLOW STRIPE to coil & condenser pack + WHITE to coil
  • RED (earth frame)
  • BROWN/BLUE: Zenor diode
  • RED to battery positive (that doesn’t make much sense)
  • BROWN/BLUE: battery negative
  • IGNITION SWITCH:  WHITE+BROWN/BLUE+BROWN/GREEN
  • FLASHER UNIT:  WHITE+LIGHT GREEN
  • REAR LIGHTS:  BROWN/GREEN STRIPE (rear lamp)+BROWN (stop lamp)+GREEN/WHITE STRIPE (L/H indicator)+GREEN/RED STRIPE (R/H Indicator)+RED (earth)
  • STOP SWITCH:  BROWN+WHITE
  • STATOR (GREEN/YELLOW STRIPE+WHITE/GREEN STRIPE)
https://monomotorcycles.co.uk/ were advertised in the UK’s BIKE Magazine…

The Motogadget is an all-in-one electrical block for all electrical items on a bike – it also provides you with a bluetooth connection so you could start and stop it by your smartphone:

https://www.motogadget.com/shop/en/electrics.html

Not really what I’m looking for for the Bonnie project, though I’ll keep it in mind for a future ground up custom build.

A new ignition barrel with keys looks to be about $80.  I’ll see if Britcycle has them.

The existing wiring looks like it was taken apart and left that way – I’m tempted to take it all out and just rewire it rather than trust the old mess.

Electrical Systems Parts List:

  • Ignition barrel & key set
  • wiring to rebuild loom step by step – I’d need correct gauge wiring & connectors
  • fuse box
  • fuses
  • reg/rectifier
  • upgraded/modernized stator

Motorcycle wiring how to: https://docs.google.com/document/d/1zm67VyrQTS1_H7WRunfkhOZ1H6wivD6RuK6194P3lvs/edit?usp=sharing  A commonly found writeup someone has done to walk any interested DIYer in how to rewire your bike.

from Blogger https://ift.tt/3FIQdai
via IFTTT

1971 Triumph Bonneville Project: Photos from the current project and long term design ideas

 Some photos from the ongoing 1971 Triumph Bonneville winter project:

One of the boxes of spares.

Spare cylinder head and engine covers.

Looking into the top of the valves…

Yep, that’s a 1984 plate sticker on it!

Front wheels cleaned up nicely.

Motor cleaned up well too!

Got it out into the minus ten sun to give it another clean up now that it’s stripped.

Strance is back to stock now that the massive chopper front shocks are gone.

The goal is to get it mechanically sorted and ride it rat-bike style next summer to iron out an kinks.  Next winter it’ll all come apart again and this time the frame will get painted and so will the body panels.  I’ve found some year correct Triumph badges but I’m thinking something a bit non-stock for the paint job, like perhaps a Gulf racing livery colour scheme:

https://www.autoevolution.com/news/gulf-racings-iconic-livery-looks-at-home-on-this-modified-yamaha-sr400-149258.html#agal_6

I’m also thinking about seats.  A plain stock seat costs the better part of $500US.  For only $100 more I could get a custom coloured Corbin seat!

https://www.corbin.com/triumph/vintlist.shtml

More research needed, but that looks sharp!  You can customize Corbin vintage seats like their modern bike seats, so I could match it to the Gulf racing colour scheme too.

from Blogger https://ift.tt/3qAxB5W
via IFTTT

The DIGITAL LENS: How Education Has Ignored A Third Foundational Fluency During The Information Revolution

I’ve been battling against digital illiteracy in Ontario’s public education system for going on a decade now and I’m frustrated at the slow rate of change.  I’ve applied for multiple positions at the board and ministry levels and watched as future administrators get moved into these positions and fail to move the needle before they evaporate off into management.  Perhaps my mistake is that I want to take on a curriculum enhancement role not to escape the classroom or to get myself into an office but to actually improve system response to an ongoing crisis that everyone else seems to want to sweep under the rug.

Considering Ontario’s current state of affairs, I’ll probably have to wait until after June 2nd for us to get a government interested in doing anything other than torturing our exceptional public education system into submission in order to hand a charter system for their donors.  When Ontario comes to its senses (if it doesn’t, I think we’re moving), I’d really like to see us address digital illiteracy, but not just for the societal benefits it would provide – my actual interest is in developing a cyber-awareness curriculum that improves Canada’s ability to survive in a networked world while also clarifying this hidden pathway for students capable and interested in pursuing it.

Unfortunately, cyber and information security aren’t foundational digital abilities, they are advanced, complex skillsets that are developed on top of more simple fluencies.  An academic comparison would be writing a complex essay of a challenging piece of writing in English class.  In order to tackle the dreaded Hamlet essay, a student would need advanced reading skills with the ability to tackle complex vocabulary and grammar that includes an understanding of both poetic syntax and the chronological difficulties inherent in reading something over four hundred years old.  This contextual challenge alone would stress most people’s language skills.  On top of all that, the writing itself is a complex set of skills developed on top of simpler abilities.  Students would need to understand spelling and grammar, and sentence construction and paragraph construction and argumentative theme development across the entire paper – it’s a staggeringly complex ask that we can only attempt in high school because we’ve placed literacy as a foundational skillset in our education system.

That was in 2010 – over a decade later Schmidt is still
trying to get people to understand the digital
revolution
that is happening around them.

With that perspective in mind, I thought I’d try and take a run at infographicking how our
analogue education system has digitized over the past twenty years.  This digitization of education has ramped up dramatically in the past decade – much of what I’ve written in Dusty World has orbited around this sea-change in digital teaching and learning.

The suddenness of this change has left many people behind.  There are administrators and ‘curriculum experts’ in our system who have never used the cloud-based learning systems we’re now required to use in every lesson.  I’m up the pointy end of digitally fluent educators in the province.  I applied for a system IT support role last year and didn’t get it – I suspect mainly because the system is incapable of understanding and appreciating digital fluency on anything but a puerile level; it’s a case of illiterate people failing to value and understand what literacy looks like; I’d really like to change that.

If we consider the education system I grew up in 1980s in Ontario, it was a very analogue place.  Teachers hand wrote notes on the board, which we copied by hand onto paper (which many students promptly lost, assuming they made the notes in the first place).  I can remember vindictive teachers doing a whole 76 minute period of note taking to ‘ready us for university’.  Nothing prepares you for university like claw hand!  These ‘lessons’ weren’t about how to take quality notes, they were about how to copy everything that was on the board as exactly and quickly as possible.  In retrospect they did nothing to prepare me for university, but they were and example of the entrenched lessons we all experienced about creating analogue content; we never had a problem with teaching analogue skills because they hadn’t changed for generations.  In the past two decades we’ve revolutionized information recording and access but we’ve also all but ignored learning best practices in these new mediums for teachers and students.

Analogue learning materials, analogue formative learning note taking leading to analogue communication of learning – and we drilled students on how to do each of these analogue exercises in order to create these skillsets.  We assume the same skills in digital spaces rather than teaching them.

My generation has been described as ‘digital immigrants’ as we arrived at the current state of affairs from a time that would seem completely alien to anyone currently under forty years old.  Along with the framing of us as digital immigrants comes the absurd framing of kids who have grown up in digital abundance as ‘digital natives‘.  If you’re read Dusty World before you know what I think of this concept (it’s absurd – just because I grew up in a time with cars didn’t mean I magically knew how to drive!).  What this lazy observation did was absolve education of the responsibility for teaching digital communications as a foundational skill, even as it became the basis for how we teach and learn.  When I tried to replicate the 20th Century Teaching & Learning above with how 21st Century Teaching & Learning has become digitized, it quickly becomes apparent that digital skills aren’t just needed to communicate your learning (it’s even how we run the literacy test now!), they are also inherent in the learning materials you receive and the formative learning you are documenting.  Many parents struggle with the new digital means of communications from their schools (online reporting and such) because of their own digital illiteracy.  If you aren’t digitally fluent, you aren’t capable of learning in an Ontario classroom in 2022.  You aren’t capable of teaching in one either, though that’s the new expectation in our on again off again emergency remote classrooms.

Learning materials are now almost entirely digital.  Even if a textbook is used it’s often digitized first so that the information in it can be shared more fluidly in digital spaces.  Staff and students need to know how to research and find information online (including curating their own which many can’t or don’t do). Formative learning is documented (when it’s documented at all) on digital notes taken in cloud based documents, though more often than not it doesn’t happen at all because we’ve lost note taking as a skill during the digital devolution revolution.  Communicating learning is now also digital with most students incapable of writing by hand legibly (part of what has killed off formative note taking).  We’ve replaced all those lessons about analogue skills with INFORMATION, because information is so readily available to us (though apparently only a minority can critically assess its value).

That digital lens is now between everything we do in education, including the traditional foundational skills of literacy and numeracy.  If you require digital fluency to teach and learn literacy and numeracy in a 2022 classroom, doesn’t that make digital fluency itself a foundational skill?  Perhaps you’re curious as to how many mandatory digital fluency programs Ontario teachers have to take?  None.  Know how many mandatory digital fluency classes there are in Ontario high schools?  None.  Know how many classes you need digital fluency in to best teach and learn?  All of them.  That is how messed up things are as 2021 ends in an ongoing pandemic that has pushed us into fully digital learning for months at a time.  Fluency is but one part of this equation.  The digital divide also includes equity issues around bandwidth and devices, but we only talk about equity when it doesn’t cost us anything.  Our ignoring of digital fluency has been a socio-economic/equity issue from the start (kids with access to tech and connectivity are obviously going to be more comfortable with it).  You might say that our lack of movement on digital fluency is simply a way to hide inequity behind something complex and difficult to deal with while still spouting about how equitable we have become.
I’m live in hope that our education system is put back on the rails and a we stop our oblivious approach to digital skills development in both teaching and learning.  If we’re going to use networked digital tools like we are, it is incumbent on every teacher to become fluent enough with it to teach best practices to their students.  Our blind leading the blind approach isn’t viable or safe and never should have happened in the first place.  Had we been working on this like we should have in the decade leading up to the pandemic, the desperate lunge into emergency remote learning could have been much more equitable and functional and done a lot to reduce the strain on families being mulched by the pandemic.
When that hope is realized I want to go after the hardest part of this in-the-land-of-the-blind skillset: cybersecurity skills.  This skillset assumes advanced ICT (information & communication technology) hardware and software skills and then, like that Hamlet essay, goes after complex, esoteric skills far beyond where most people will operate.  I want Ontario to develop a cyber-awareness curriculum that brings all users of networked technology (that’s pretty much everyone in the province) up to a point where their digital illiteracy is no longer a detriment to the province.  Illiterate users are still the biggest threat in cybersecurity and I’d like to get everyone to the point where they aren’t oblivious to how the digital world they’re living their lives in works so that they can not only learn and teach more effectively in our digital systems but also better protect their data privacy and online presence.
I’d also like to clear away the obstructions our digitally illiterate education system has placed in front of the most digitally adept students and clear pathways into jobs in critical ICT infrastructure, most especially in cybersecurity.  If we don’t take steps to secure our digital infrastructure, everything else fails (electricity, water & gas all depend on IT).
We should be producing graduates with the digital fluency needed to confidently make their way in our brave new world while also clarifying pathways for those students willing and able to protect everyone else from an increasingly threatening threatscape.

HOW TO ENGAGE EDUCATION WITH CYBERSECURITY

https://prezi.com/view/7pqMzlLdfOFltD78ILP6/

Over the past couple of years I’ve done a fair bit of writing for various provincial and national agencies around cyber-education.  In every case they seemed to be looking for an in-and-out, short duration of work online course they could post that teachers and students would magically flock to.  Having presented on cybersecurity education in the classroom both face to face pre-pandemic and online once it kicked off, I became aware of just how fearful most staff are in engaging with this subject that jumps up and down on their digital doubts while also threatening them with horrible outcomes that they don’t understand.  Throwing up an online course isn’t going to bridge this fear/illiteracy gap.

Having worked with CyberTitan and Field Effect (an Ottawa based cybersecurity provider) on a joint federal government/private enterprise/public education presentation at the NICE K-12 Cybersecurity Education Conference this past December, we presented on how with industry expertise, federal vision and provincial public education community outreach we could make cyber-pathways available to all pathways interested students while also offering immersive and meaningful cloud-based simulations that are equitably available to all.

ICTC did an ICT Teacher Champion Day pre-COVID where they provided interested and engaged teachers with resources and support.  I think this approach is how you bypass the fear and get staff and students to engage with scary-cyber on a basic fluency level.  It would also present competition opportunities that clarify pathways for the most cyber-interested.  By finding local champions who are willing/able to engage others in cyber-skills development, we could connect and walk people through some of that dormant online material and actually produce a change in how we’re doing things.  This requires boots on the ground and a longer term commitment than throwing together an online course.
As digital fluency becomes a mandatory part of our public school experience and we begin producing more digitally fluent teachers and students, we can up our game in advanced digital areas like cybersecurity and emerging technologies like machine learning and 3d modelling and create digitally skilled graduates who aren’t self-taught and potentially dangerous young adults who put our economy and communities at risk.
There is much to do.  I’m looking forward to being part of an Ontario that is ready to take on this challenging future even as it hatches around us.

from Blogger https://ift.tt/32s5Qol
via IFTTT

Digital Footprint 2.0

SOURCES

The source(s) of this post (and a good example of the richness of thinking you can get out of an online PLN):

@MzMollyTL’s Digital Footprint discussion from ECOO last year that stirred up the new teachers in my AQ.


@melaniemcbride’s comment on the sweatshop mentality of the always on teacher:

https://twitter.com/melaniemcbride/status/230841214180683779

@dougpete’s blog on edublogging:
http://dougpete.wordpress.com/2012/08/03/this-week-in-ontario-edublogs-27/

…which led to some interesting questions about online presence:

http://dougpete.wordpress.com/2012/08/05/dont-hurt-yourself-with-social-media/

Phew!  That is a lot of build up!  Here I go…


DIGITAL FOOTPRINT 2.0

I think we’re ready for an evolution in what our expectations are around this.  Diana’s original presentation suggested that teachers need to familiarize themselves with online media, and that is still true.  However, since that presentation there have been political upheavals supported by social media, underground poltical movements powered by social media, and I’m currently watching the  ‘Twitter Olympics’: the first really social media powered Olympic games.  Even the forth estate is grudgingly trying to manage the tidal wave of social media.  Merely familiarizing yourself isn’t going to cut it anymore.  Ignoring it will make you irrelevant to your students with astonishing speed.

Social media is becoming mainstream and there are increasing expectations that people know how to use it.  Only in extremely staid, conservative situations (educational administration) is social media being shunned.  Even the very conservative family reunion I attended recently wanted to start making use of social media to keep in touch, and these were people who play banjos.  Social media is becoming ubiquitous, even unhooking the Ontario government’s ability to manipulate media into justifying its agenda.  This is a powerful force, not something to be trifled with or poked at tentatively.  If you’re going to do it, do it honestly, and be yourself.  You’ll find the ability to expand your interests online empowering if you don’t try and game it.

POCKET NETWORKS

The social networks we see spring up like mushrooms in the rain are being prompted by the miniaturization of computer hardware.  Smartphones are increasingly common, and since 2010, the vast majority of ‘phone’ use has been in data, not voice.  We use our mobile computers as interconnected computers, not as phones.  Our students do it, we do it, even boomers are doing it.  Like the telegraph, then the telephone after it, this is a revolution in how we communicate with each other, and almost everyone is carrying around the means in their pockets.

Our classrooms have more processing power in the pockets of students than desktop labs did ten years ago.  Their ability to communicate is unparalleled in history, and disregards geography like no other telecommunications system before it.  Just hoping that everyone considers doing something with their online presence is no longer enough, and ignoring or banning the hardware that is causing this is turning a blind eye to a profound shift in social communications.  Schools that ban smartphones should be banning other new inventions, like electricity, telephones, televisions… which very quickly starts to look backward.

GENUINE ONLINE PRESENCE

Being online offers you an opportunity to be anonymous, but this requires a great deal of work on your part.  The nature of the internet means you’re always leaving digital bread crumbs about how and where you’re communicating from.  Anti-web types will use this as an excuse to harp on privacy issues, but when have we ever been able to communicate privately?  Gossip has always been and always will, and what you say has always followed you, it just follows you in an amplified manner now.  Social media allows you to broadcast gossip.  If you were a gossip before, you’re a digitally enhanced gossip now.  It’s never been more important to be the best person you are in public; there is a record now, and I’ve seen students constantly bitten by this as their Facebook updates land them in the VP’s office.

Trying to be someone else is exhausting!

The genuine self as an online presence offers an opportunity to meet others beyond your geographic situation that share your interests.  You quickly find yourself a part of an online community that reflects your predilections and offers you a sense of collaborative discourse that might be missing in your workplace, or your immediate geography.  If you’re genuine in expressing your interests, you’ll create a genuinely satisfying social media ecosystem.  If you fabricate yourself, or limit yourself to specific identities (your teacher self comes to mind here), you won’t be exploring the actual usefulness of this new medium.

The other advantage of being genuine online is that you attract meaningful dialogue.  If you’re one dimensional, you tend to attract n00bs, marketing interests and bots (who are also one dimensional).  If you’re genuine and human in your presentation of self, you’ll attract a richer class of connection, one that offers powerful insights regardless of where you are in relation to each other on the planet.  You’re harnessing the true potential of social media when you are multi-dimensional and human in your approach to it.

Developing a digital footprint is no longer about simply participating, or creating a cardboard cutout of your professional self, it’s about honestly expressing your own views in a genuine manner.  The myriad of apps and means of communicating in a social network allow you to express yourself in simple (twitter), complex (blog) or focused interests (Google+, Facebook) ways.  Knowing how to use the tools effectively is key.

If you’re fabricating a professional appearance, well, that’s just work, and doing it all summer, 24/7 is not going to do you any real good.  Ultimately, you’re doing an awful lot of work and not exploring this new medium effectively, probably because you’re scared of it.

School Leadership 2.0

Several school administrators made comments in Doug’s blog about the need for restraint.  In a leadership role, you’re not free to fly off the handle whenever you have an opinion.  You always need to consider the working relationship you have to foster.  Having said that, George’s comment about social media being a useful tool in fostering a team based on real knowledge of each other suggests that social media can be a means of allowing people who might not otherwise to know each other better.

The tendency has been for management (union, board, ministry, and any other ed-based management you can suggest) to shy away from social media.  They fear the de-centralization of power, and see it as a threat to their dominance.  It’s nice to know some administrators are fighting this tendency, but I’ve heard of many more who don’t hire the best candidates because their online presence creates unease, and in worst cases not considering hiring a teacher at all because they are familiar with the social web that most students spend their lives in.  Why they think that hiring belligerent, intentionally irrelevant teachers is a good idea is beyond me.

What I love about social media is that it is democratizing information.  No longer do we have to succumb to the broadcast media’s idea of what is true.  Twitter told me about Bin Laden hours before broadcast media would, or could.  As a social media-ist, I’m responsible for vetting my own information feed, and broadcasting my own truth.  As both a leader, and a professional, this means not being a jackass, but being a meaningful social mediaist requires this from the get go.  If you’re going to do social media well, being a gossip, spreading untruths, will eventually turn the crowd on you.  Generating drama and controlling spin doesn’t work very well in a democratized information medium; the truth just bypasses you.

Social media is an opportunity to build a more ideal information medium, one without favoritism or fabrication, one that does not favor the status quo in order to maintain it; the crowdsourced truth is dangerously unmanageable… and free from spin.  

As a member of that tribe I try not to let invective and one-up-man-ship dictate my actions, I try to be collaboratively engaging.  This isn’t contrary to any professional or leadership role I may have; in fact, it should enhance those roles.  When you broadcast your actions, it behooves you to it well.

CONCLUSION: THE REVOLUTION IS HAPPENING, REGARDLESS

The social media revolution has harnessed mobile electronics and the internet to produce a democratized media frenzy.  Old-school, forth estate media is floundering, trying to manage their loss of broadcasting monopoly, but still seeing it as an immanent threat.  Other power structures are also frustrated by this decentralization of voice.  Where once a hierarchy could dictate the message, now social media swirls around these old-school broadcasting roadblocks.  

Unions are watching members broadcast their opinions directly, without being able to dictate a unified response.  Governments and corporations are finding that the dictatorial control they once had over traditional media is weakening, because traditional media matters less.  As social media responses bypass traditional censorship, we once again see the many assert their power.

There is no doubt that these changes will force a fundamental shift in how we work with each other.  This kind of radical, data driven transparency gives control freaks a nervous breakdown, but in the end, I can’t believe that freeing the signal from the self-involved interests of the powerful isn’t better for everyone; that it will result in fairer, transparent, more effective organizations.

As educators, we have to try and get a grip on this ourselves, and then be ready to try and (usefully) assist our students in effectively navigating this exciting, historical change.  It’s no longer enough to pay some attention to what your digital footprint is.  It’s no longer enough to do the minimum necessary.  If we’re going to teach future generations how to survive in the rough sea of democratized data we’ve made for them, we need to adapt and master the waves ourselves.

A relevant educator is recognizing the radical nature of these changes and is doing their best to create a genuine online persona, one that accurately reflects the public persona they demonstrate in their physical life.  What’s private isn’t at issue here, but our public selves are changing, and it doesn’t do anyone any good to try and game social media by making cardboard cutouts of themselves online.


Some things to consider:
Dancing in the Datasphere: a philosophical look at where we are going
The Singularity: an inside look at what Silicon Valley believes is coming

Don’t kid yourself, you’re living in the middle of a revolution!


Sense of Satisfaction and some more Concours 3d models

It was a tough week with an empty garage, but the Connie passed safety and it’s now licensed and ready to put on some miles, I just have to wait for the snow to stop.  The ride back from shop was -8°C (minus thirteen with the windchill, minus a million when you’re riding in it).  With any luck we can get some above zero temperatures soon and I can finally take the big ‘un for a long ride.

It was gratifying to have a pro look over the bike and judge it well put together.  Considering all the work I’ve done on it, it feels like a real validation.

Since I’m with-bike again, I took another run at 3d modelling it…